cm100du-34ka application general purpose inverters & servo controls, etc mitsubishi igbt modules cm100du-34ka high power switching use i c ................................................................... 100a v ces .......................................................... 1700v insulated type 2-elements in a pack feb. 2009 8.85 (8.25) (18) circuit diagram c2e1 e2 c1 g2e2 e1 g1 4 0.5 0.5 25.7 0.5 0.5 e1 e2 g2 g1 cm c1 e2 c2e1 label 4-6. 5 mounting holes 3-m6 nuts 108 29 +1.0 ?.5 62 18 7 18 7 18 8.5 22 93 0.25 48 0.25 2.8 4 7.5 6156 (7) 17.5 14 14 14 25 2.5 21.5 25 t c measured point (7.5) (7.5) outline drawing & circuit diagram dimensions in mm not recommend for new design
2 feb. 2009 gate-emitter threshold voltage collector-emitter saturation voltage thermal resistance *1 v ce = v ces , v ge = 0v v ge = v ges , v ce = 0v t j = 25 c t j = 125 c v cc = 1000v, i c = 100a, v ge = 15v v cc = 1000v, i c = 100a v ge = 15v r g = 3.1 ? , inductive load i e = 100a i e = 100a, v ge = 0v, t j = 25 c i e = 100a, v ge = 0v, t j = 125 c igbt part (1/2 module) fwdi part (1/2 module) case to heat sink, thermal compound applied *2 (1/2 module) case temperature measured point is just under the chips i c = 10ma, v ce = 10v i c = 100a, v ge = 15v v ce = 10v v ge = 0v 1700 20 100 200 100 200 890 ?0 ~ +150 ?0 ~ +125 3500 3.5 ~ 4.5 3.5 ~ 4.5 400 mitsubishi igbt modules cm100du-34ka high power switching use symbol v v w c c v rms n ?m n ?m g a a 1 0.5 4.0 14 2.4 0.75 350 150 550 800 600 4.6 0.14 0.24 0.09 * 3 ma a nf nc c v v k/w 3.2 3.8 450 5.8 2.2 0.04 5.5 v v ns 47 ns collector cutoff current gate leakage current input capacitance output capacitance reverse transfer capacitance t otal gate charge t urn-on delay time t urn-on rise time turn -off delay time t urn-off fall time reverse recovery time reverse recovery charge emitter-collector voltage contact thermal resistance thermal resistance i ces i ges c ies c oes c res q g t d(on) t r t d(off) t f t rr ( note 1 ) q rr ( note 1 ) v ec( note 1 ) r th(j-c) q r th(j-c) r r th(c-f) r th(j-c? q symbol parameter v ge(th) v ce(sat) note 1. i e , i em , v ec , t rr , q rr & die/dt represent characteristics of the anti-parallel, emitter-collector free-wheel diode (fwdi). 2. pulse width and repetition rate should be such that the device junction temperature (t j ) does not exceed t jmax rating. 3. junction temperature (t j ) should not increase beyond 150 c. 4. pulse width and repetition rate should be such as to cause negligible temperature rise. * 1 : case temperature (tc) measured point is indicated in outline drawing. * 2 : typical value is measured by using thermally conductive grease of = 0.9[w/(m ?k)]. * 3 : if you use this value, r th(f-a) should be measured just under the chips. collector-emitter voltage gate-emitter voltage maximum collector dissipation junction temperature storage temperature isolation voltage w eight g-e short c-e short t c = 25 c pulse (note 2) t c = 25 c pulse (note 2) t c = 25 c terminals to base plate, f = 60hz, ac 1 minute main terminals m6 screw mounting m6 screw t ypical value parameter collector current emitter current t orque strength conditions unit ratings v ces v ges i c i cm i e ( note 1 ) i em ( note 1 ) p c ( note 3 ) t j t stg v iso unit t yp. limits min. max. t est conditions maximum ratings (tj = 25 c, unless otherwise specified) electrical characteristics (tj = 25 c, unless otherwise specified) not recommend for new design
3 feb. 2009 mitsubishi igbt modules cm100du-34ka high power switching use 200 120 160 40 80 0 0246810 output characteristics (typical) collector current i c (a) collector-emitter voltage v ce (v) t j = 25c 11 12 10 9 8 v ge = 20v 15 14 160 80 200 120 40 0 048121620 transfer characteristics (typical) collector current (a) gate-emitter voltage v ge (v) v ce = 10v t j = 25c t j = 125c 6 5 4 3 1 2 0 0 160 40 12080 200 collector-emitter saturation voltage characteristics (typical) collector-emitter saturation voltage v ce (sat) (v) collector current i c (a) v ge = 15v t j = 25c t j = 125c 10 8 6 4 2 0 20 68 12 16 10 14 18 gate-emitter voltage v ge (v) collector-emitter saturation voltage characteristics (typical) collector-emitter saturation voltage v ce (sat) (v) t j = 25c i c = 200a i c = 100a i c = 40a 10 0 2 3 5 7 10 1 2 3 5 7 10 2 10 3 2 3 5 7 12345 free-wheel diode forward characteristics (typical) emitter current i e (a) emitter-collector voltage v ec (v) t j = 25c 10 ? 10 ? 10 0 2 3 5 7 10 1 2 3 5 7 10 2 2 3 5 7 2 10 0 357 2 10 1 357 2 10 2 357 capacitance? ce characteristics (typical) capacitance c ies , c oes , c res (nf) collector-emitter voltage v ce (v) c ies c oes c res v ge = 0v performance curves not recommend for new design
4 feb. 2009 mitsubishi igbt modules cm100du-34ka high power switching use 10 1 10 2 23 57 10 3 23 57 10 1 10 2 2 3 5 7 10 3 2 3 5 7 t rr i rr reverse recovery characteristics of free-wheel diode (typical) emitter current i e (a) reverse recovery time t rr (ns) reverse recovery current l rr (a) conditions: v cc = 1000v v ge = 15v r g = 3.1? t j = 25c inductive load 10 1 10 ? 10 ? 10 ? 10 0 7 5 3 2 10 ? 7 5 3 2 10 ? 7 5 3 2 7 5 3 2 10 ? 23 57 23 57 23 57 23 57 10 1 10 ? 10 ? 10 0 10 ? 10 ? 7 5 3 2 10 ? 7 5 3 2 10 ? 3 2 23 57 23 57 single pulse t c = 25c transient thermal impedance characteristics (igbt part & fwdi part) normalized transient thermal impedance z th (j?) (ratio) time (s) igbt part: per unit base = r th(j c) = 0.14k/ w fwdi part: per unit base = r th(j c) = 0.24k/ w 0 4 8 16 12 20 0 100 300 600 200 500400 gate charge characteristics (typical) gate-emitter voltage v ge (v) gate charge q g (nc) v cc = 800v v cc = 1000v i c = 100a 10 1 10 2 57 10 3 23 57 10 2 2 3 5 7 10 3 2 3 5 7 10 4 2 3 5 7 10 1 23 half-bridge switching characteristics (typical) switching times (ns) collector current i c (a) conditions: v cc = 1000v v ge = 15v r g = 3.1? t j = 125c inductive load t d(off) t d(on) t f t r not recommend for new design
|
